If you have discovered a cracked support beam, a rotted post, a sagging patio cover, or another structural wood problem, one of your first questions is probably: How much does post and beam repair cost?
In Albuquerque, a relatively minor post or beam repair may cost approximately $250 to $800, while moderate structural wood repairs often range from $800 to $2,500 or more. Replacing a single structural beam may cost between $2,000 and $6,000 or more, and larger projects involving multiple beams, support posts, footings, engineering, or extensive finish work can reach $6,000 to $15,000 or more.
These are general planning ranges, not fixed prices.
The price can change significantly based on whether the damaged wood is decorative or load-bearing, how easily workers can reach it, whether temporary supports are needed, and how much hidden damage is uncovered after the project begins.
This guide explains typical post and beam repair costs in Albuquerque, the factors that affect your estimate, and how to determine whether repair or complete replacement is the better investment.
Average Post and Beam Repair Cost in Albuquerque
The following ranges can help you establish a preliminary budget:
| Type of post or beam project | General planning range |
|---|---|
| Small cracks, surface deterioration, sealing, or minor localized repair | $250–$800 |
| Moderate wood repair or localized reinforcement | $800–$2,500+ |
| Support-post repair or replacement | Often $1,000–$4,000+ |
| Single structural beam replacement | $2,000–$6,000+ |
| Multiple posts and beams or complex structural rebuilding | $6,000–$15,000+ |
| Structural engineering inspection or basic report, when needed | Approximately $350–$800+ |
A basic structural engineer’s inspection or report commonly costs several hundred dollars, although stamped plans, detailed calculations, follow-up visits, and complex designs can cost considerably more.
Your project may fall below or above these ranges. A short, exposed beam over a one-story patio is very different from a long beam carrying part of a home’s roof. Two beams may appear nearly identical from the outside but require completely different repair methods once their loads, connections, and internal condition are evaluated.
That is why an on-site inspection is usually necessary before a contractor can provide a reliable estimate.
What Is Included in a Post and Beam Repair Estimate?
A detailed estimate should cover more than a new piece of wood.
Depending on the project, the total structural wood repair cost may include:
- Inspection of the damaged post, beam, connections, and surrounding structure
- Removal of finishes or materials blocking access
- Temporary shoring to support the structure during the repair
- Removal and disposal of damaged wood
- Custom cutting and fitting of new structural material
- Repair or replacement of brackets, fasteners, anchors, or connectors
- Modification or replacement of a footing or post base
- Structural reinforcement
- Staining, sealing, painting, or finish matching
- Permit and inspection coordination
- Structural engineering, when required
- Repairs to nearby stucco, roofing, ceilings, trim, or other finishes
- Cleanup and disposal
An estimate that only lists the cost of lumber does not provide an accurate picture of the project. On many structural repairs, the material itself is only one part of the expense. Safe access, temporary support, custom fitting, and restoration of surrounding finishes may require more time than installing the replacement beam.
Why Post and Beam Repair Costs Vary So Much
Structural wood repairs do not have a simple per-foot price that works for every home. Several conditions can cause the final estimate to increase or decrease.
1. Whether the Post or Beam Is Load-Bearing
The most important question is whether the damaged piece is supporting a structural load.
A decorative beam may be repaired or replaced without supporting the roof or floor above it. A load-bearing beam may carry:
- Roof rafters
- Ceiling joists
- A patio roof
- An upper floor
- Exterior walls
- Additional beams
- Concentrated loads from other structural components
Before a load-bearing beam is removed, the weight it carries must be supported temporarily and transferred safely to the new structure. This process is commonly called shoring.
Temporary support may involve adjustable posts, framed support walls, beams, cribbing, or other methods appropriate for the structure. Shoring must remain stable while the damaged material is removed and the new beam, post, or connection is installed.
The need for temporary support increases labor, equipment, and planning costs, but it is essential for protecting the home and everyone working on it.
2. The Length and Size of the Beam
A short beam supporting a small porch usually costs less to replace than a long timber spanning a large patio or living area.
Longer spans may require:
- Larger solid-sawn timbers
- Engineered lumber
- Built-up beams
- Steel reinforcement
- Additional posts
- Larger footings
- More workers or lifting equipment
- Special delivery or handling
Beam depth and thickness also matter. A large timber is heavier, harder to maneuver, and more expensive to purchase and finish than a smaller structural member.
The replacement cannot simply match the visible dimensions of the existing beam. It must be appropriately sized for the span, load, material, wood species, grade, and connection details.
3. The Type and Extent of the Damage
Not all cracks or deteriorated areas mean the entire beam has failed.
Minor surface checking is common in exposed timber, especially in New Mexico’s hot, dry climate. Wood naturally loses moisture and shrinks as it dries, which can create cracks along the grain. Some checking is cosmetic, while deeper cracks near joints or heavily loaded areas may require closer evaluation. El Pueblo Woodworking identifies intense sunlight, dry air, temperature changes, moisture, insects, and aging connections as common contributors to post and beam deterioration in New Mexico.
Repair may be possible when damage is:
- Limited to a small area
- Primarily cosmetic
- Confined to the surface
- Not affecting a critical connection
- Not reducing the structural capacity of the wood
- Caused by a problem that can be corrected
Replacement becomes more likely when there is:
- Deep rot
- Major splitting
- Crushing at a connection
- Significant sagging
- Widespread insect damage
- Separation between structural members
- Loss of material at a post base
- Movement that continues to worsen
- Damage across a large portion of the beam
- A beam that is undersized for the load
The more wood that must be removed, reinforced, or replaced, the higher the likely cost.
4. Accessibility
Accessibility can make a major difference in the price to fix a sagging beam or post.
An exposed post at the edge of a patio may be relatively easy to reach. A beam located above a finished ceiling, inside an adobe wall, underneath a second floor, or behind stucco may require significant preparation.
Difficult access may require:
- Removing drywall or ceiling material
- Opening stucco
- Removing roofing
- Taking down trim
- Moving cabinets or built-ins
- Using scaffolding
- Protecting finished floors
- Working around landscaping
- Temporarily removing doors or windows
- Using lifting equipment
The repair itself may be straightforward, but reaching the damaged area and restoring the finishes afterward can add substantial labor.
5. Temporary Shoring Requirements
Some posts and beams can be repaired with minimal temporary support. Others must be unloaded completely before work begins.
The contractor must determine:
- What the damaged member supports
- Where temporary supports can be placed
- Whether the floor or slab can carry the temporary load
- How the load will be transferred
- How much movement has already occurred
- Whether the structure can be raised gradually
- How long the shoring must remain in place
A sagging structure may not always be returned immediately to its original position. Raising a beam too quickly can crack drywall, separate roofing materials, damage windows, or create movement elsewhere in the home.
Projects involving extensive shoring generally cost more because they require additional material, setup, labor, and careful sequencing.
6. The Replacement Material
Material selection affects both the initial cost and the long-term performance of the repair.
Possible materials include:
- Douglas fir
- Cedar
- Pine
- Oak
- Glued laminated timber
- Laminated veneer lumber
- Built-up dimensional lumber
- Pressure-treated wood
- Steel or concealed metal reinforcement
El Pueblo Woodworking’s post and beam services include material options such as cedar, Douglas fir, and oak, selected according to the project’s structural and visual requirements.
A concealed structural beam may allow the use of engineered lumber. An exposed beam may need to match the grain, proportions, texture, stain, and architectural character of the home.
Premium timber, custom milling, hand-distressing, specialty joinery, and finish matching can raise the cost, but these details may be important in Pueblo-style, Territorial, rustic, or custom Southwestern homes.
7. Footing and Foundation Conditions
A new post is only as reliable as the surface supporting it.
If a support post has settled, tilted, or rotted at the bottom, the problem may not be limited to the wood. The footing or post base may also be inadequate.
Possible footing-related problems include:
- A post resting directly on soil
- An undersized concrete footing
- A cracked footing
- Poor drainage
- A loose or corroded anchor
- A post base buried in concrete
- Improper separation between wood and soil
- Settlement beneath the support
- Water collecting around the bottom of the post
Correcting the wood without correcting the footing can allow the same problem to return.
A project that requires excavation, concrete work, new reinforcement, curing time, or upgraded anchors will cost more than a wood-only repair. Albuquerque’s homeowner permit guide notes that porch and carport posts require footings and that beams must be sized for calculated roof loads.
8. Connection and Hardware Damage
Beams and posts work as a system. Even sound wood can move or sag if the connections are failing.
A contractor may inspect:
- Post caps
- Post bases
- Bolts
- Screws
- Nails
- Joist hangers
- Straps
- Brackets
- Anchors
- Traditional wood joinery
- Connections to walls or roof framing
Loose, rusted, undersized, or incorrectly installed hardware may need to be replaced. Custom metal brackets or concealed structural connectors may be required when standard hardware does not fit the design.
Replacing a few fasteners may be inexpensive. Rebuilding several structural connections can add substantially to the total.
9. Finish Matching and Cosmetic Restoration
An exposed structural beam is often an architectural feature as well as a working part of the building.
Once the structural work is complete, the new material may need to be:
- Sanded
- Textured
- Distressed
- Stained
- Painted
- Sealed
- Color matched
- Blended with existing timbers
Matching an older finish can take experimentation and multiple applications. Existing wood may have darkened, faded, weathered, or developed a patina that new lumber does not naturally have.
A basic structural replacement that will be hidden behind drywall may cost less than an exposed timber replacement that must look as though it has always been part of the home.
10. Permits and Engineering
Structural repair work may require a building permit, a minor alteration and repair permit, construction drawings, or engineering details.
The City of Albuquerque states that remodeling work not specifically exempt from permitting generally requires a permit, although some smaller projects may qualify for a minor alteration and repair permit. The city also calculates building-permit and plan-review fees according to the project’s valuation, including labor and materials.
New Mexico’s residential permit guide generally requires permits before regulated buildings are altered or repaired unless a specific exemption applies. It also requires framing plans to identify the size, spacing, span, grade, and species of structural wood members.
Whether engineering is required depends on the project and the authority reviewing it. Engineering is more likely when:
- A major load-bearing beam is being replaced
- The original structure has moved significantly
- The existing framing is unusual
- The beam span is long
- Steel is being added
- The load path is unclear
- A footing must be redesigned
- The structure does not match standard framing tables
- The repair uses an alternative design or method
- Permit reviewers request stamped calculations
The City of Santa Fe also processes building permits and inspections through its Land Use Department, so Santa Fe homeowners should confirm requirements for the property before work begins.
Post and Beam Repair Cost by Type of Project
The following examples show how different types of repairs may fit into the general pricing ranges.
Minor Surface Cracks and Weather Damage: $250 to $800
Smaller projects may involve surface checking, localized weather damage, minor finish failure, or a small non-structural damaged area.
The work might include:
- Cleaning the wood
- Removing loose material
- Filling or stabilizing a small damaged area
- Sanding
- Applying stain or sealer
- Correcting a minor moisture source
- Replacing a small piece of trim
This price range is most appropriate when the wood remains structurally sound and access is easy.
A crack should still be inspected when it is growing, located near a connection, accompanied by sagging, or deep enough to affect a substantial portion of the beam.
Moderate Structural Wood Repair: $800 to $2,500 or More
Moderate repairs may involve a larger localized area, a damaged beam end, deteriorated hardware, a partially rotted post, or reinforcement of a structural connection.
Possible work includes:
- Removing localized rot
- Installing a carefully fitted wood repair
- Reinforcing a beam
- Adding structural hardware
- Repairing a connection
- Replacing a post base
- Correcting water exposure
- Rebuilding a small section of surrounding material
The price depends heavily on whether the structure must be supported temporarily and whether the finished repair will remain visible.
Support-Post Repair or Replacement: Often $1,000 to $4,000 or More
A support post may need attention when the bottom has rotted, the post is leaning, the connection has failed, or the footing has settled.
A straightforward post replacement may include:
- Supporting the beam above
- Removing the damaged post
- Inspecting the footing and connections
- Cutting a new post
- Installing an appropriate post base and cap
- Securing the connections
- Finishing the new wood
- Removing the temporary supports
Costs increase when the footing must be replaced, the beam must be raised, surrounding finishes must be removed, or the new post must be custom-milled to match an existing design.
Single-Beam Replacement: $2,000 to $6,000 or More
A basic single-beam replacement may fall within this range when the beam is exposed, accessible, and supporting a relatively straightforward one-story structure.
The project becomes more expensive when:
- The beam is unusually long or heavy
- Multiple workers are required to lift it
- A crane or material lift is needed
- The beam is located inside the house
- Roofing or stucco must be removed
- The beam supports an upper floor
- Electrical wiring or plumbing is nearby
- Custom joinery is required
- Engineering is necessary
- The beam must match an older architectural finish
National support-beam replacement estimates often extend to approximately $10,000 for more complicated work, showing why an on-site assessment is more useful than relying on an average alone.
Multiple Posts, Beams, and Structural Components: $6,000 to $15,000 or More
A larger structural project may involve:
- Several deteriorated posts
- More than one beam
- New footings
- Extensive temporary shoring
- Replacement of roof framing
- Rebuilding a patio cover
- Repairing surrounding stucco or roofing
- Engineering plans
- Permit inspections
- Custom fabrication and finishing
At this point, the project may be closer to a partial structural rebuild than a simple repair.
The estimate should identify which elements will be preserved, which will be replaced, and what is included in restoring adjacent materials.
Is It Cheaper to Repair or Replace a Structural Wood Beam?
Repair is generally less expensive when the damage is small, stable, and limited to one area.
However, the lowest immediate price is not always the lowest long-term cost.
Suppose a beam has deep rot across several feet, major splitting near the bearing point, and ongoing water exposure. A localized patch might cost less today, but it may not restore sufficient strength or prevent more damage. Replacing the beam and correcting the water source could provide a safer and more durable result.
Repair is more likely to make sense when:
- Most of the beam remains structurally sound
- Damage is localized
- The original member is properly sized
- Connections remain reliable
- The cause of damage can be corrected
- The repair can transfer loads safely
- Preserving the original timber is architecturally important
Replacement is more likely to make sense when:
- Rot or insect damage is extensive
- The beam is severely sagging
- The beam is undersized
- A large crack crosses a critical load area
- The wood is crushed at its bearing point
- Several previous repairs have failed
- Connections cannot be restored reliably
- The cost of repairing the existing beam approaches the cost of replacement
El Pueblo Woodworking’s repair-versus-replacement guidance emphasizes that not all visible damage requires replacement, but severe rot, sagging, instability, or widespread deterioration may make replacement the safer long-term option.
How Much Does It Cost to Replace a Support Beam in a New Mexico House?
For budgeting purposes, the cost to replace a support beam in a house in New Mexico may begin around $2,000 for a smaller, accessible project and rise beyond $10,000 for a complicated interior or multi-story replacement.
A house beam generally costs more to replace than an exposed patio beam because the work may require:
- Opening ceilings or walls
- Protecting interior finishes
- Supporting floors or roof framing
- Moving electrical, plumbing, or ductwork
- Installing a concealed beam
- Repairing drywall and paint
- Engineering the new load path
- Coordinating permit inspections
A beam carrying a second floor may require much more extensive shoring than a beam carrying a lightweight patio roof.
Homeowners should also distinguish between replacing an existing damaged beam and installing a new beam after removing a load-bearing wall. Although the projects involve similar structural principles, wall-removal projects may include demolition, utility relocation, drywall work, flooring repair, and substantial interior finishing.
How Much Does It Cost to Fix a Sagging Beam?
The price to fix a sagging beam depends on why it is sagging.
Possible causes include:
- An undersized beam
- A span that is too long
- A failed support post
- A settled footing
- Rot at the beam end
- Loose or failed connections
- Excessive roof or floor load
- Long-term deflection
- Structural alterations made by a previous owner
Simply pushing the beam upward may not solve the problem. The underlying cause must be corrected, and the structure may need to be raised gradually.
A localized repair could cost less than $2,500. Replacing the beam, adding posts, rebuilding footings, or repairing related framing may bring the project into the $3,000 to $10,000-plus range.
The contractor may also need to determine whether returning the beam to its original position would damage finishes or place stress on other parts of the structure.
Albuquerque and Santa Fe Conditions That Affect Structural Wood
New Mexico’s dry climate does not eliminate wood deterioration. It creates a different combination of risks.
Intense Sunlight
Exposed posts and beams receive strong ultraviolet exposure. Over time, sunlight can break down finishes, fade the wood, and dry the outer fibers.
A failed finish allows moisture to enter more easily during storms while also allowing the timber to dry unevenly afterward.
Large Temperature Changes
Wood expands and contracts as temperature and moisture conditions change.
Repeated movement may contribute to:
- Cracked finishes
- Open joints
- Loose fasteners
- Twisted beams
- Gaps between components
- Surface checking
Monsoon Moisture and Roof Leaks
A dry climate can make a small leak easier to overlook. Water may only reach the wood during certain storms, but repeated wetting can eventually cause rot.
Common moisture sources include:
- Leaking roofing
- Failed flashing
- Water running down stucco
- Irrigation overspray
- Poor drainage
- Posts in contact with soil
- Water collecting on horizontal surfaces
Insects
Termites and other wood-destroying insects can damage structural material, particularly where moisture is present or wood contacts the ground.
A repair estimate may change if deteriorated wood is opened and previously hidden insect damage is discovered.
Older and Custom Construction
Many homes in Albuquerque and Santa Fe include exposed vigas, rustic timbers, portals, patios, and custom wood details.
Repairing these structures may require more than standard framing carpentry. The replacement may need to preserve the home’s proportions, joinery, finish, and Southwestern architectural character.
Warning Signs That Should Be Inspected
Contact a qualified professional when you notice:
- A visibly sagging beam
- A leaning support post
- A roofline that appears uneven
- Deep or widening cracks
- Wood that feels soft or spongy
- Dark staining or recurring moisture
- Crumbling wood fibers
- Gaps forming at joints
- Loose brackets or bolts
- Rusted structural hardware
- A post pulling away from its footing
- Doors or windows becoming difficult to operate near the damaged area
- New ceiling or wall cracks
- Visible insect tunnels or discarded wings
- A cracking or shifting sound during wind or roof loading
Visible sagging, severe rot, or active movement should not be treated as a cosmetic problem.
Consider limiting use of the affected area until it can be evaluated, especially when the damage involves a patio roof, porch, carport, upper floor, or part of the main house.
Can You Repair a Rotted Beam Without Replacing the Entire Beam?
Sometimes.
A localized beam-end repair may be possible when the deterioration is limited and enough sound wood remains to transfer the required loads. The repair method depends on the location, load, remaining wood, and connection details.
Possible professional approaches include:
- Removing and replacing a localized damaged section
- Installing a precisely fitted wood repair
- Adding a sister member
- Using engineered reinforcement
- Installing structural plates or brackets
- Rebuilding the bearing connection
- Adding a new support post
Not every method is appropriate for every beam. A filler or cosmetic patch does not automatically restore structural capacity.
When rot has spread through a large portion of the beam, replacement is usually more practical and reliable.
Most importantly, the source of moisture must be corrected. Otherwise, the repaired or replaced material may develop the same problem.
Does Homeowners Insurance Cover Post and Beam Repair?
Coverage depends on what caused the damage and the terms of the policy.
Insurance may be more likely to cover sudden damage caused by a covered event, such as a storm or impact. It is less likely to cover gradual deterioration, neglected maintenance, long-term leaks, ordinary weathering, or insect damage.
Homeowners should document:
- The visible damage
- When it was first noticed
- Any recent storm or impact
- Water intrusion
- Contractor findings
- Engineering reports
- Repair estimates
- Photographs taken before work begins
Contact the insurance carrier before making permanent repairs when a covered claim may be involved. Emergency stabilization may still be necessary to protect the structure from additional damage.
Can You Replace a Structural Beam Yourself?
Replacing a load-bearing beam is generally not an appropriate do-it-yourself project.
Mistakes can cause:
- Partial structural collapse
- Roof movement
- Cracked walls and ceilings
- Damaged windows or doors
- Failed connections
- Uneven load transfer
- Foundation damage
- Serious personal injury
- Permit or inspection problems
The work requires more than removing one piece of wood and installing another. The structure must be supported, the new material must be correctly sized, and the loads must be transferred through posts, walls, connections, and footings.
Even an experienced homeowner may not be able to identify every load carried by the beam.
Professional repair also provides a documented scope of work, which can be important when selling the property or addressing future inspection questions.
How to Reduce Your Structural Wood Repair Cost
You should not reduce costs by skipping necessary structural work, but there are practical ways to keep the project manageable.
Address Damage Early
A small area of failing finish is much less expensive to correct than extensive rot.
Schedule an inspection when you first notice movement, water staining, or a significant crack.
Correct the Source of the Problem
Repair roof leaks, failed flashing, poor drainage, or irrigation overspray before replacing the wood.
Otherwise, you may pay for the same repair again.
Preserve Sound Material
Not every post or beam needs to be replaced simply because one component is damaged.
A careful evaluation may allow the contractor to preserve sound wood while replacing only the failed section.
Keep the Work Area Accessible
Moving furniture, decorations, planters, and stored items can reduce setup time. Do not remove structural finishes or attempt demolition unless the contractor directs you to do so.
Compare Complete Scopes, Not Just Totals
A lower estimate may exclude engineering, permits, finish work, hardware, disposal, or repair of surrounding materials.
Ask each contractor to explain:
- What will be removed
- What will be installed
- How the structure will be supported
- What materials will be used
- Whether finishes are included
- Whether permits are included
- How hidden damage will be handled
- What warranty applies
The best estimate is the one that clearly explains what you are purchasing.
What to Expect During a Post and Beam Inspection
A professional evaluation usually begins with a visual inspection of the damaged component and the surrounding structure.
The contractor may look at:
- The beam span
- Post locations
- Roof or floor framing
- Bearing points
- Connections
- Footings
- Moisture patterns
- Wood condition
- Existing repairs
- Movement or deflection
- Access limitations
- Finish requirements
You may be asked:
- When did you first notice the problem?
- Has the damage changed?
- Is there a known roof leak?
- Has the structure been remodeled?
- Does water collect nearby?
- Has the post or beam been repaired previously?
- Do you have original plans?
- Are there cracks inside the house near the damaged area?
After the inspection, the contractor should be able to explain whether the project appears to involve maintenance, localized repair, reinforcement, or replacement.
A structural engineer may be recommended before final pricing when load calculations or stamped plans are needed.
Illustrative Post and Beam Cost Examples
Every home is different, but the following scenarios show how project scope affects cost.
Example 1: Weathered Patio Beam With Minor Surface Checking
The beam remains straight and structurally sound, but the finish has failed and several shallow checks have appeared.
Possible scope:
- Cleaning
- Minor surface preparation
- Localized filling or stabilization
- Sanding
- New exterior finish
Possible planning range: $350 to $800.
Example 2: Rotted Bottom of One Patio Support Post
The beam above must be supported temporarily. The damaged post is removed, the footing is inspected, and a new post base and finished wood post are installed.
Possible planning range: $1,500 to $3,500.
The cost could be higher if the footing must be rebuilt or the beam has also deteriorated.
Example 3: Replacement of One Accessible Patio Beam
A medium-length beam under a one-story patio roof is replaced. The project includes temporary support, removal, a new timber, hardware, and finishing.
Possible planning range: $3,000 to $6,000.
Custom timber, restricted access, engineering, or roofing work could increase the total.
Example 4: Multiple Posts and Beams With Footing Repairs
Several supports have deteriorated due to poor drainage. The project requires shoring, new concrete footings, replacement posts, one replacement beam, hardware, and finish restoration.
Possible planning range: $7,500 to $15,000 or more.
These examples are for budgeting only. They are not substitutes for an inspection or written estimate.
Choosing a Post and Beam Repair Contractor in Albuquerque
Structural woodwork requires a combination of construction knowledge, woodworking skill, and attention to architectural detail.
Ask prospective contractors:
- Do you regularly work with exposed posts and beams?
- How will you determine whether the component is load-bearing?
- How will the structure be supported during the repair?
- Will the new wood match the existing dimensions and finish?
- Who will determine the required beam size?
- Could an engineer be needed?
- Are permits included?
- Will damaged hardware be replaced?
- Are footing repairs included?
- How will hidden damage affect the price?
- Who will restore stucco, roofing, trim, or ceilings?
- Is cleanup included?
- What warranty applies to the work?
A responsible contractor should be willing to explain why a particular repair method is recommended.
Be cautious of anyone who gives a firm structural replacement price without seeing the beam, understanding what it supports, or evaluating access.
Get a Detailed Post and Beam Repair Estimate From El Pueblo Woodworking
The only reliable way to determine your actual post and beam repair cost is to have the structure evaluated in person.
At El Pueblo Woodworking, we provide custom post and beam repair, replacement, and construction services for homeowners in Albuquerque, Santa Fe, and surrounding New Mexico communities. Our team combines structural problem-solving with detailed woodworking, material selection, and finish matching.
We can evaluate damaged posts, beams, connections, and surrounding woodwork and then explain whether repair, reinforcement, or replacement offers the best long-term solution.
El Pueblo Woodworking is based in Albuquerque and emphasizes custom craftsmanship, detailed estimates, honest communication, and materials selected for New Mexico homes.
Do not wait for a sagging beam, rotted post, or loose connection to become a larger structural problem.
Contact El Pueblo Woodworking at (505) 221-5321 to request an evaluation and detailed post and beam repair estimate in Albuquerque or Santa Fe.
